Phone
Email
FacebookInstagramXLinkedIn
ASHNET Logo

D-Link Router Settings

Set your D-Link router to DHCP and tag VLAN 10 – the steps and menu names for D-Link firmware.

Before you start

Connect the router's WAN / internet port to the port on your fibre box (ONT) that we activated – it is in your activation email, and it is usually the one with the light on. Then open the router's settings page.

D-Link settings page
Settings page192.168.0.1 (some models 192.168.1.1)
Sign in withadmin / the password on the router label

1. Set the internet connection to DHCP

  1. Go to Settings > Internet > IPv4.
  2. Set My Internet Connection is to Dynamic IP (DHCP).
  3. Save.

2. Tag the internet VLAN (VLAN 10)

  1. Go to Settings > Internet > VLAN (on some firmware Advanced > VLAN).
  2. Turn VLAN on and set Internet VLAN ID to 10 with Priority 0. Leave the IPTV and VoIP rows off unless we have told you otherwise.
  3. Save; the router reconnects.

3. Check it works

Give the router a minute, then look at its status page: the WAN or internet section should show an IP address from us. Open a website to confirm. If the WAN stays blank, the VLAN or the DHCP setting has not taken – check both, then restart the router.

On the DSL/DVA models, add an Ethernet WAN connection (not ADSL/VDSL) before setting DHCP and the VLAN.

D-Link models

A settings page for each D-Link model we have seen on New Zealand fibre. If yours is not here the steps above still apply – the menus are the same across the brand.

D-Link AC3200 DIR-890LSettings guideManufacturer’s page
D-Link AX1800 DIR-X1860Settings guideManufacturer’s page
D-Link COVR-2202 AC2200 / D-Link COVR-1203Settings guideManufacturer’s page
D-Link DIR-1760 AC1750Settings guideManufacturer’s page
D-Link DIR-300 Wireless G RouterSettings guideManufacturer’s pageNot compatible
D-Link Dir-615 N300Settings guideManufacturer’s page
D-Link DIR-825 AC1200Settings guideManufacturer’s page
D-Link DIR-853 AC1300Settings guideManufacturer’s page
D-Link DIR-878Settings guideManufacturer’s page
D-Link DIR-879 AC1900Settings guideManufacturer’s page
D-Link DIR-882 AC2600Settings guideManufacturer’s page
D-Link DSL-2877A/ 2877AL ADSL2+Settings guideManufacturer’s page
D-Link DSL-2878Settings guideManufacturer’s page
D-Link DSL-2885A AC1200Settings guideManufacturer’s page
D-Link DSL-2888ASettings guideManufacturer’s page
D-Link DSL-2900AL AC1900Settings guideManufacturer’s page
D-Link DSL-3890Settings guideManufacturer’s page
D-Link DSL-4320L AC3200Settings guideManufacturer’s page
D-Link DSL-5300Settings guideManufacturer’s page
D-Link DSL-X1852ESettings guideManufacturer’s page
D-Link DVA-2800Settings guideManufacturer’s page
D-Link EAGLE PRO AI G415 (AX1500)Settings guideManufacturer’s page
D-Link EAGLE PRO AI R15Settings guideManufacturer’s page
D-Link G415 AX1500Settings guideManufacturer’s page
D-Link M15 Eagle Pro AX1500Settings guideManufacturer’s page
D-Link M30 AX3000Settings guideManufacturer’s page
D-Link M60 AX6000Settings guideManufacturer’s page

The ASH NET settings in full

ASH NET fibre settings
Connection typeDynamic IP / DHCP (also called IPoE or "obtain an IP automatically")
Username & passwordNone – ASH NET does not use PPPoE
VLAN ID10, tagged (802.1Q) on the internet connection
VLAN priority (802.1p)0
MTU1500
IPv6Optional – leave on automatic
Router portThe WAN / internet port, into the lit port on the fibre box (ONT)

Routers we recommend

These arrive set up for ASH NET – plug them into the fibre box and they work. On a 12-month plan you can rent one for $7.50 a month instead of buying.

TP-Link HX510 AX3000Wi-Fi 6, pre-configured for ASH NET$149.50 incl. GSTTP-Link VX230v AX1800Wi-Fi 6 with a phone port for your home line$149.50 incl. GSTMercusys Halo H47BEWi-Fi 7 mesh for Hyperfibre$299 incl. GST

Still stuck? Email [email protected] with the router make and model and a photo of the screen, or call 09 269 4000. We can also supply a pre-configured router – see the shop.

All brands